1
1
Quality Woodworking Machinery including •Clamps, Clamping Racks, Multi Rotating Clamping Systems •Glue Applicators •Band Saws •Multi Bores •Thicknessers and Planers •Dust Extractors •Edge Banders •Panel Saw, Rip Saws and Docking Saws •Titebond Glue •And Much More........
Awisa 2008
STAND 4227 - 4231
EDGEBANDING MACHINES
MAGNUM HA RANGE EDGEBANDER MACHINES
STANDARD FEATURES:
Variable heat control switch with cooling-off settings.
Single phase 240 volt electrics throughout.
Sheet steel machine body with anti-friction strips on work table.
Driven polyurethane pressure roller after edgestrip application position.
Complete with foot pedal control of cut-off guillotine – used when shaped workpiece will not activate table limit switches.
Shaped panels can be edged by removing outfeed fence.
Sheet steel tray to support rolls of edgestrip.
Note: No flush end trimming or top and bottom trimming.
MAGNUM MODEL HA100 BENCH EDGEBANDER MACHINE
For pre-glued edgestrip.
1250 watt heater/blower unit to re-activate glue.
Electric cut-off guillotine for roll-edgestrip (melamine or veneer) – controlled by 2 limit switches in work table.
Click here for Product Data Sheet on the HA100.(PDF 108kb)
MAGNUM MODEL HA120 BENCH EDGEBANDER MACHINE
For pre-glued edgestrip up to 2mm thick.
1500 watt heater/blower unit to re-activate glue.
Pneumatic cut-off guillotine for roll-edgestrip (melamine, PVC or veneer) – controlled by 2 limit switches in work table.
Click here for Product Data Sheet on the HA120.(PDF 115kb)
MODEL KDT-150 GLUE POT TYPE EDGEBANDING MACHINE For edgestrip 0.4mm to 2mm thick

The KDT-150 is a compact automatic edgebanding machine designed to apply and trim edgestrip from 0.4mm melamine to 2mm PVC onto straight panels from 12mm to 45mm thick, with automatic through feed of the panels and built to provide reliable, accurate edge banding for many years of operation.

FEATURES:
Pneumatic guillotines flush trim the excess tape from each end and large 80mm diameter top and bottom cutterheads flush trim thin melamine edge tape and 2mm radius trim the thicker 2mm PVC edging.
A small glue pot with heating elements heats the glue to application temperature. 
Glue is applied to the panel edge by a glue roller.
A round support table on the rear of the machine holds the roll of edgestrip ready to be fed into the machine.
The accuracy of the machine is assured by a heavy frame onto which all the working units are mounted. 
A digital readout is fitted to the adjustment for working height.
An adjustable support beam to hold wide panels is mounted on two sliding bars on the front of the machine. 
The overhead belt driven feed unit and all the working units are covered by sheet metal safety guards.
Click here for Product Data Sheet on the KDT-150.(PDF 87kb)

ARRON CORNER ROUNDING MACHINE
Simple to use and produces a great finish.
No more filling or sanding corners.


Click here for Product Data Sheet on the Corner Rounding Machine.(PDF 185kb)
MODEL KDT 300 SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1. Hot melt glue pot application station with heated fence.
2. Edgestrip application station with pneumatic guillotine.
3. Five-roller pressure station with pneumatic pressure.
4. End trimming station – cut-off saws with angle adjustment.
5. Top & bottom trimming station – tiltable to 45º, with 2mm radius cutters.
Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large window in safety hood for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on height setting on top beam for different panel thickness.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Heavy weight machine @ 1500kgs.
Click here for Product Data Sheet on the KDT 300.(PDF 120kb)
MODEL KDT 360 SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1. Hot melt glue pot application station with heated fence.
2. Edgestrip application station with pneumatic guillotine.
3. Five-roller pressure station with pneumatic pressure.
4. End trimming station – cut-off saws with angle adjustment.
5. Top & bottom trimming station – tiltable to 45º, with 2mm radius cutters.
6. Top and bottom scraper station to fine finish PVC edging.
7. Top and bottom mop buffing station.
Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large window in safety hood for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on height setting on top beam for different panel thickness.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buff units mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ 1880kgs.
Click here for Product Data Sheet on the KDT-360.(PDF 125kb)
MODEL KDT 360D SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1. Hot melt glue pot application station with heated fence.
2. Edgestrip application station with pneumatic guillotine.
3. Five-roller pressure station with pneumatic pressure.
4. End trimming station – cut-off saws with angle adjustment.
5. Top & bottom trimming station – tiltable to 45º, with 2mm radius cutters.
6. Top and bottom scraper station to fine finish PVC edging.
7. Top and bottom mop buffing station.
Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large window in safety hood for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on height setting on top beam for different panel thickness.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buff units mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ 1880kgs.
Click here for Product Data Sheet on the KDT 360D.(PDF 122kb)
MODEL KDT 450 SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1. Hot melt glue pot application station with heated fence.
2. Edgestrip application station with pneumatic guillotine.
3. Five-roller pressure station with pneumatic pressure.
4. End trimming station – cut-off saws with angle adjustment.
5. Top & bottom trimming station – tiltable to 45º, with 2mm radius cutters.
6. Corner rounding station with two motorised cutter units to travel around curved ends of panels.
7. Top and bottom scraper station to fine finish PVC edging.
8. Top and bottom mop buffing station.

Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large window in safety hood for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on height setting on top beam for different panel thickness.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buff units mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ 1880kgs.
Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning. Glue pot temperature standby switch.
Fluorescent light inside safety hood. High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up. Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large windows in safety hoods for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on motorised height setting on top beam for different panel thicknesses.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buff units mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ approx. 2500kgs.
Click here for Product Data Sheet on the KDT 450.(PDF 143kb)
MODEL KDT 450D SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1.       Hot melt glue pot application station with heated fence.
2.       Edgestrip application station with pneumatic guillotine.
3.       Five-roller pressure station with pneumatic pressure.
4.       End trimming station – cut-off saws with angle adjustment.
5.       First top and bottom trimming station – tiltable to 15º with 12mm straight cutting tips.
6.       Second top and bottom trimming station – tiltable to 45º, with 2mm radius cutters.
7.       Corner rounding station with two motorised cutter units to travel around curved ends of panels.
8.       Top and bottom scraper station to fine finish PVC edging.
9.       Top and bottom mop buffing station.

Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large windows in safety hoods for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on motorised height setting on top beam for different panel thicknesses.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Disposable tungsten carbide tip tooling on top and bottom trimmers and corner rounding units.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buff units mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ approx. 2680kgs.
Click here for Product Data Sheet on the KDT 450D.(PDF 148kb)
MODEL KDT 450DJ SINGLE SIDED AUTOMATIC EDGEBANDING MACHINE
Features:
1.       Twin spindle jump pre- milling station with pneumatic movement.
2.       Hot melt glue pot application station.
3.       Edgestrip application station with pneumatic guillotine.
4.       Five-roller pressure station with pneumatic pressure.
5.       End trimming station – cut-off saws with angle adjustment.
6.       First top & bottom trimming station – tiltable to 15º with 12mm straight cutting tips.
7.       Second top & bottom trimming station – tiltable to 45º, with 2mm radius cutters.
8.       Corner rounding station with two motorised cutter units to travel around curved ends of panels.
9.       Top and bottom scraper station to fine finish PVC edging.
10.   Top and bottom mop buffing station.

Full safety covers over motorised cutting and trimming units.
Convenient electrical control panel at infeed position.
Change set-up from 0.4mm to 2mm edgestrip with one switch on electrical control panel.
Teflon lined glue pot allowing easy cleaning.
Glue pot temperature standby switch.
Fluorescent light inside safety hood.
High feed rates – 12, 16 or 20 metres/min.
Feed jogging button to assist setting up.
Pneumatic shut-off gate on glue roller.
Front and rear tape overlap adjustment from electrical control panel.
Large 3” (75mm) dust exhaust hoses on trimming units for efficient extraction.
Large windows in safety hoods for better visibility.
Five independent pressure rollers – pneumatic pressure.
Pneumatic gate prevents panels being fed in too close to one another.
Mechanical digital readout on motorized height setting on top beam for different panel thicknesses.
Precision German slideways on cut-off saws.
European high frequency motors on saws and trimmers.
Cut-off saws and trimmers can be set on angle.
Diamond tipped 140mm diameter cutterheads on twin spindle pre-milling station.
Pneumatic blowers on scraper tracer wheels to keep swarf from affecting accuracy.
Mop buffs mounted on 50mm round bars – will not flex under load.
1440rpm motors on buffs to prevent scorching.
Heavy weight machine @ approx. 2890kgs.
Length of machine – 7.6 metres.
Click here for Product Data Sheet on the KDT 450DJ.(PDF 128kb)
 
Disclaimer:
 Weldline Engineering Pty Ltd maintains a constant program of product research and development and retains the right to change specifications without notice.  It is recommended that the prospective purchaser ensure that this web site correctly identifies the products described herein. 
©2008 Weldline
Telephone Number: +61 8 8280 6441
Site Designed by: Costa Designs